Land-pride AT2572 User Manual Page 14

  • Download
  • Add to my manuals
  • Print
  • Page
    / 28
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 13
12
Section 2: Operating Instructions
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
8/08/12
Land Pride
Table of Contents
Maximum PTO driveline Movement During Operation
Figure 2-3
Shortening the PTO Shafts
Figure 2-4
Checking Driveline Minimum Length
Refer to Figure 2-4:
1. Start tractor and slowly engage 3-point to move
lower arms until the gearbox shaft is approximately
level with tractor's PTO shaft.
2. Slide inner yoke of the driveline over the gearbox
shaft and secure with locking collar.
3. Slide outer yoke of driveline over the tractor PTO
shaftandsecure with lockingcollar. Skip to step 5on
page 12 if driveline fits between tractor and gearbox.
IMPORTANT: Some tractors are equipped with
multi-speed PTO ranges. Be certain your tractor ‘s
PTO is set for 540 rpm.
IMPORTANT: Avoid premature driveline
breakdown. A driveline that is operating must not
exceed an angle of 25 degrees up or down while
operating the 3-point lift. See Figure 2-3 below.
13800
IMPORTANT: Always check driveline minimum
length during initial setup, when connecting to a
different tractor and when alternatingbetween using
aquickhitch and astandard3-point hitch. Morethan
one driveline may be required to fit all applications.
IMPORTANT: Itis necessaryto aligning thetractor’s
PTO shaft level with the gearbox shaft when
checking driveline minimum length. Too long a
driveline can damage tractor, gearbox and driveline.
22009
4. The driveline will require shortening if it is too long to
fit between tractor and gearbox. Shorten drivelineas
follows:
a. Raise or lower 3-point lower arms until gearbox
and tractor PTO shafts are approximately level
with each other. Securely block mower frame in
this position.
b. Settractorinpark,shuttractorengineoff,setpark
brake and remove switch key.
c. Pull driveline apart into two sections as shown in
Figure2-4.Attachouterdrivelineuniversaljointto
the tractor PTO shaft. Attach inner driveline
universal joint to the gearbox shaft. Pull on each
driveline section to be sure universal joints are
secured to the shafts.
d. Hold driveline sections parallel to each other to
determineiftheyaretoolong.Theinnerand outer
shieldsoneachsectionshouldendapproximately
1" short of reaching the universal joint shield on
the adjacent section (see “B” dimension). If they
are too long, measure 1" (“B” dimension) back
from theuniversaljointshieldandmake a mark at
this location on the inner and outer driveline
shields.
e. Cut off inner shield at mark (“X” dimension). Cut
same amount off inner shaft (“X1 dimension).
Repeat cut off procedure (“Y”&“Y1 dimensions)
to cut outer driveline half.
f. Remove all burrs and cuttings.
5. Apply multi-purpose grease to the inside of the outer
driveline shaft and reassemble the two shafts.
6. Attach inner driveline yoke to the gearbox shaft.
7. Attach outer driveline yoke to the tractor's PTOshaft.
8. Thedrivelineshould nowbemovedbackand forth to
insure that both ends are secured to the tractor and
gearbox PTO shafts. Reattach any end that is loose.
9. Hook one of the driveline safety chains in a hole on
the outer driveline yoke shield and the opposite end
to the tractor to restrict outer shield rotation.
10. Hook the second driveline safety chain in a hole on
the inner driveline yoke shield and the opposite end
to the mower to restrict inner shield rotation.
11. Start tractor and raise the Grooming Mower just
enough to remove blocks used to support the mower
frame in step 4a above.
12. Slowlyengage the tractor’shydraulic3-pointto lower
the mower. Check for sufficient drawbar clearance.
Move drawbar ahead, aside or remove if required.
IMPORTANT: Two small chains are supplied with
the driveline. These chains must be attached to
outer and inner driveline yoke shields and to the
cutter deck and tractor to restrict driveline shields
from rotating.
Page view 13
1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 27 28

Comments to this Manuals

No comments